| AMSOIL
Synthetic Powershift Transmission Fluids are Recommended
for Applications Requiring the Following Specifications:
- Caterpillar
TO-4
- Allison
C-4
- HD
Torque and Drivetrain
- Eaton
Fuller CD-30 (SAE 30)
- Eaton
Fuller CD-50 (SAE 50)
AMSOIL Synthetic Powershift
Transmission Fluids are specifically designed for heavy-duty
powershift transmissions. Formulated for extended drain
intervals, AMSOIL Synthetic Powershift Transmission Fluids
contain top-quality synthetic basestocks and a high level
of top-quality additives selected specifically for powershift
transmission performance. They offer unmatched transmission
friction performance, smooth brake operation, reduced
gear and bearing wear and increased equipment life. AMSOIL
Synthetic Powershift Transmission Fluids extend time between
overhauls.
AMSOIL
Synthetic SAE 50 Powershift Transmission Fluid exceeds
Fuller CD-50 performance specification and is ideal for
use in Fuller, Rockwell, Spicer, Fabco, Warner and other
large truck manual transmissions.
Friction
Characteristics
AMSOIL Synthetic Powershift Transmission Fluids are compatible
with common metallic and nonmetallic friction materials.
AMSOIL Synthetic Powershift Transmission Fluids' stable
frictional characteristics eliminate the problems of excessive
brake noise and vibration, clutch slippage, friction surface
deposits and design material degradation.
AMSOIL
Synthetic Powershift Transmission Fluids are formulated
for fast, smooth clutch engagements and wet brake operations;
excellent power transmission through clutches and synchronizers;
and superior hydraulic fluid performance for servo equipped
units.
Wear
Protection
AMSOIL Synthetic Powershift Transmission Fluids exceed
the wear requirements of the Caterpillar TO-4 specification.
AMSOIL Synthetic Powershift Transmission Fluids are formulated
without viscosity index improvers for superior shear stability.
They maintain grade throughout service life, due to their
superior shear stability, providing long-term protection
against equipment wear, even when equipment is frequently
subjected to sustained periods of applied pressure or
high horsepower and high torque.
High
and Low Temperature Performance
In high temperatures, AMSOIL Synthetic Powershift Transmission
Fluids dependably protect components from wear. Their
superior oxidative and thermal stability inhibits the
formation of varnish, deposits and sludge so equipment
runs clean. AMSOIL Synthetic Powershift Transmission Fluids
are excellent heat transfer fluids and may help hot-running
equipment operate up to 50° F cooler and keep them
running in their optimal temperature range. In low temperatures,
AMSOIL Synthetic Powershift Transmission Fluids flow readily
for dependable startup and post-startup protection.
Copper
Corrosion, Rust and Foam Inhibition
AMSOIL Synthetic Powershift Transmission Fluids protect
equipment from copper corrosion and rust, even during
equipment storage. AMSOIL Synthetic Powershift Trans-
mission Fluids do not foam in service, protecting equipment
from the metal-to-metal contact and wear that occurs with
use of foam-filled fluids.
Installation
AMSOIL Synthetic Powershift Transmission Fluids are fully
compatible with other fluids used in powershift applications.
To install AMSOIL Synthetic Powershift Transmission Fluids,
drain the fluid in the system,, replace the filter (if
so equipped) and install the appropriate AMSOIL Synthetic
Powershift Transmission Fluid.
Service
Life
AMSOIL Synthetic Powershift Transmission Fluids provide
two to five times the service life of conventional petroleum
fluids if AMSOIL Synthetic Powershift Transmission Fluids
are kept free of dirt and moisture.
AMSOIL
Synthetic Powershift Transmission Fluids may be used for
250,000 miles or five years (whichever comes first) in
manual transmissions.
AMSOIL
Limited Warranty
Typical
Technical Properties |
| AMSOIL
SAE 10W, 30 and 50 Synthetic Powershift Transmission
Fluids
(CTG, CTJ, CTL) |
| Product
Code |
CTG |
CTJ |
CTL |
| SAE
Viscosity Grade |
10W |
30 |
50 |
| ISO
Viscosity Grade |
32 |
68 |
150 |
| Kinematic
Viscosity @ 100° C, cSt (ASTM D-445) |
6.3 |
11.1 |
18.6 |
| Kinematic
Viscosity @ 40° C, cSt (ASTM D-445) |
34.9 |
77.5 |
151.6 |
| Viscosity
Index (ASTM D-2270) |
131 |
132 |
138 |
| Flash
Point °C (°F) (ASTM D-92) |
252
(486) |
254
(489) |
268
(514) |
| Fire
Point °C (°F) (ASTM D-92) |
272
(522) |
278
(532) |
296
(565) |
| Pour
Point °C (°F) (ASTM D-97) |
-54
(-65) |
-43
(-45) |
-36
(-33) |
| Four
Ball Wear Test 40 kg. 75°C, 1200 rpm, 1 hour
(ASTM D-4172 B) |
0.35 |
0.35 |
0.35 |
| Noack
250°C, 1 hour, percent weight loss (DIN 51581) |
5.8 |
4.8 |
5.2 |
|
